← Micro:bit

Appendix

Expansion Boards for micro:bit

แผงวงจรขยายความสามารถของ micro:bit

  • The micro:bit is capable on its own, but its edge connector is hard to wire and its power is small.
  • An expansion board (แผงวงจรขยายความสามารถ) fixes that: the micro:bit plugs into it and gets power, easy pins and motor drivers.
  • This appendix covers three popular INEX boards: one for prototyping, one for learning and one for robots.

Why Use Expansion Boards? ทำไมต้องใช้แผงวงจรขยายความสามารถ

micro:bit edge connector ↓ slot in Expansion board socket + circuits adds Power steady 3.3 V / 5 V, a DC jack Easy pins IDC, JST, 4 mm rings Drivers servo and DC motor Inputs knob, buttons, extra ADC
The micro:bit slides into the board's socket. The board then adds what the micro:bit lacks.

Problem 1: the pins are hard to use

0 1 2 3V GND 5 big 4 mm rings (easy to clip) + small gold pads (hard to clip)
Only five pins are big rings that a crocodile clip can grip. The rest are small gold pads.
  • The edge connector has 5 big 4 mm rings: 0, 1, 2, 3V and GND.
  • All the other pins are very small gold pads. Ordinary wires do not grip them.
  • A board brings every pin out to a plug or socket you can wire easily.

Problem 2: the power is too small

micro:bit 3.3 V, ~300 mA DC motor 5–6 V, more mA Alone: too weak Battery / adapter Expansion board +3.3 V to micro:bit +5/6 V to motors Motors / servos With a board: works
Motors need more voltage and current than the micro:bit's 3.3 V pin can give, so a board adds a separate power path.
  • The micro:bit's own 3.3 V supply gives up to about 300 mA. That is too little for strong loads.
  • DC motors and servo motors need 5 V to 6 V and often several hundred mA.
  • So a board brings its own power circuits and motor drivers.

The 3 INEX expansion boards at a glance

PROJECT:BIT #7200665 Compact I/O 67 × 50 mm 4 servo ports 9 IDC pin headers Prototyping AX-microBIT+ #830032 Learning board upright or flat mount knob on P2 5 clip rings Classroom iBIT+ #8000480 Robot controller 2 × 1 A DC motors 2 servo ports 8 × 12-bit ADC Robots
Three boards, three jobs: PROJECT:BIT prototypes, AX-microBIT+ teaches, iBIT+ drives robots.
Feature PROJECT:BIT AX-microBIT+ iBIT+
Part number#7200665#830032#8000480
micro:bit mountSocket80-pin, upright or flat80-pin
Power in+5 V and +3 V circuitsDC jack +5 to +16 VJack or screw terminal, +4.8 to +16 V
Servo ports4 (P8, P12, P13, P14)None listed2 (P8, P12), +6 V
DC motor driversNoneNone2 × 1 A H-bridge
Analog extrasNoneKnob on P2ADS7828, 8 channels, 12-bit
I2C port4-pin IDCNone listedSDA and SCL
Clip rings (4 mm)None5: P0, P1, P2, +3V, GND5: P0, P1, P2, +3V, GND

Which board for which project?

Wheels or DC motors? Yes iBIT+ No 3 or 4 servo motors? Yes PROJECT:BIT No Learning with clips, a knob, breadboard? Yes AX-microBIT+ No PROJECT:BIT small and simple
Answer the questions from the top. The first Yes picks your board.

Next: PROJECT:BIT Board Details →

PROJECT:BIT (#7200665) บอร์ดอินพุตเอาต์พุตขนาดเล็กสำหรับ micro:bit

  • A small input/output board with IDC connectors.
  • Good for building many kinds of projects and inventions.
  • Only 67 × 50 mm.

Block diagram

Power in +3 V regulator +5 V regulator micro:bit in the socket 9 IDC I/O I2C port (4-pin) Buttons A and B 4 servo headers SV1–SV4 P8 P12 P13 P14 powered at +5 V signals
Power goes through two regulators. +3 V feeds the board and the micro:bit; +5 V feeds the servos.

Technical features

  • A socket that holds the micro:bit.
  • Push buttons wired to micro:bit buttons A and B, for easy use.
  • 9 three-pin male IDC connectors: P0, P1, P2, P8, P12, P13, P14, P15 and P16, for sensors and outside devices.
  • I2C bus connector: 4-pin male-female IDC, for an OLED screen or a digital I2C sensor.
  • 4 servo motor connectors: on P8, P12, P13 and P14.
  • Dual power circuits: +5 V for servos, and a steady +3 V for the whole board including the micro:bit.
  • Metal standoffs with M3 threads, so the board mounts easily on a frame or base plate.
P0 P1 P2 P8 P12 P13 P14 P15 P16 I/O header (IDC, 3 pins each) also a servo output (SV1–SV4) 9 headers in all; 4 of those pins also drive servos.
Which pins go where. P8 and P12 are shared: they are both on the I/O headers and on servo headers.

Next: AX-microBIT+ Prototyping Board →

AX-microBIT+ (#830032) บอร์ดอินพุตเอาต์พุตสำหรับการเรียนรู้

  • A learning board with a flat connector, so the micro:bit can be mounted upright or flat.
micro:bit upright vertical slot micro:bit, flat horizontal slot stands up lies down
Two mounting choices: the micro:bit can stand up in the vertical slot or lie down in the horizontal one.

Block diagram

DC jack +5 to +16 V Reverse protection +3.3 V regulator on/off switch micro:bit 80-pin slot 4 mm rings ×5 JST sensor ports A and B buttons Knob → P2
One DC jack feeds a protected +3.3 V supply. Everything the micro:bit has is brought out to easy connectors.

Technical features

  • 80-pin connectors, upright and flat, for the micro:bit.
  • An on/off switch for the board.
  • A DC jack for +5 V power, a steady +3.3 V circuit and reverse-polarity protection.
  • JST connectors for the important ports, to join INEX input/output devices.
  • Every micro:bit port as male and female IDC, so wiring to a breadboard is easy.
  • Five 4 mm gold-plated rings for crocodile clips, wired to P0, P1, P2, +3V and GND.
  • Two push buttons wired to micro:bit buttons A and B.
  • Potentiometer on the board: read analog input on P2 straight away.
  • Two-layer PTH circuit board, with gold plating on all solder points.
3.3 V knob GND wiper Pin P2 analog read pin P2 0 to 1023
The knob is a voltage divider: turn it and the voltage on P2 slides from 0 to 3.3 V. The ADC reads 0 to 1023.

Next: iBIT+ Mobile Robotics Controller →

iBIT+ (#8000480) แผงวงจรควบคุมหุ่นยนต์สำหรับ micro:bit

  • An add-on that lets the micro:bit control mechanical parts and read sensors.
  • Use it to build robots or programmable automatic machines.

Block diagram

Power in +4.8 to +16 V jack / screws +3.3 V switching +6 V for servos micro:bit 80-pin socket 5 JST ports + 5 clip rings 2 DC motor drivers 1 A each, H-bridge 2 servo ports (P8, P12) I2C: ADS7828 ADC 8 inputs, 12-bit (0–4095) +6 V powers the servo ports Motors: BO1, BO2, MG1 gear sets, Tamiya 1.5–3 V
Wide power input feeds two regulators. The micro:bit commands motor drivers, servos and an I2C ADC chip.

The extra ADC: 12 bits against the micro:bit's 10

micro:bit 10-bit 0 1023 ADS7828 12-bit (on iBIT+) 0 4095 Both: 0 V at the left end, 3.3 V at the right end. 12 bits = 212 = 4096 levels.
The ADS7828 splits the same 0 to 3.3 V range into 4096 steps, four times finer than the micro:bit's 1024.

Technical features

  • An 80-pin connector for the micro:bit.
  • Wide power input +4.8 to +16 V: DC jack and screw terminal block, with reverse-polarity protection.
  • A steady +3.3 V switching regulator for the whole board, and +6 V for the servo motors.
  • 5 JST 3-pin I/O ports for INEX sensors: P0, P1, P2, P8 and P12.
  • 8 analog inputs (ADC0 to ADC7) from the ADS7828 chip. Input range is 0 to +3.3 V at 12-bit resolution (0 to 4095).
  • I2C 2-wire bus (SDA and SCL) for more I2C devices.
  • Five 4 mm gold-plated rings for crocodile clips, wired to P0, P1, P2, +3V and GND.
  • 2 DC motor drivers: 1 A output each, with status lights. IDC and screw terminals. Power comes straight from the battery. They work with BO1 and BO2 gear sets, the metal MG1 geared motor, and Tamiya 1.5 V and 3 V motors.
  • 2 servo motor ports on P8 and P12, powered straight from the battery through the +6 V regulator (+Vm).

Next: Interactive Expansion Boards Explorer →

Interactive Expansion Boards Explorer

  • Hover over or tap any part on the real photos of the three boards.
  • Each part shows what it is for.
🔍

PROJECT:BIT (#7200665) Hardware Anatomy

Interactive Map
PROJECT:BIT Board Real Photo
👉

Hover or tap the Edge Socket, 4-Channel Servos, or DC Regulator on PROJECT:BIT to explore.

🔍

AX-microBIT+ (#830032) Activity Board Anatomy

Interactive Map
AX-microBIT+ Board Real Photo
👉

Hover or tap the Banana Jacks, Potentiometer, or DC Power Jack on AX-microBIT+ to explore.

🔍

iBIT+ (#8000480) Robotics Controller Anatomy

Interactive Map
iBIT+ Robotics Board Real Photo
👉

Hover or tap the Dual Motor Drivers, ADS7828 12-bit ADC, or Servo ports on iBIT+ to explore.

Next: Test Your Knowledge with the Quiz →

Expansion Boards Review & Self-Check

  • Check what you remember about why an expansion board is needed, and what each of the three INEX boards is built for.
PROJECT:BIT 4 servo ports small, 67 × 50 mm AX-microBIT+ knob wired to P2 upright or flat iBIT+ 2 × 1 A DC motors 8 × 12-bit ADC
Quick reference: the one thing each board is best at.
1. How many of the 25 edge-connector contacts are the big 4 mm ring holes?
2. How much current can the micro:bit supply on its own 3.3 V rail?
3. Which board is built for a mobile robot with two DC motors?
4. How many servo channels does PROJECT:BIT provide?
5. Which board has a potentiometer already wired to pin P2?
6. The ADS7828 on iBIT+ converts to 12 bits. What is its top reading?
7. Which connector lets a board take an OLED screen or a digital sensor?
8. Why do these boards include reverse-polarity protection?